Do You Nail Starter Strips Tight For Vinyl Siding
When information technology comes to installing vinyl siding, there are several building tricks you should accept in your back pocket to produce the best results. Amongst the most important is the positioning of the starter and trim strips, which is the purpose of this postal service.
So, read on, equally we have discussed in detail how to install vinyl siding starter and trim strips the correct way. We too tell you what starter and trim strips are and why they are important in your installation.
Materials Needed to Install Vinyl Siding Starter & Trim Strips
The materials and tools listed below tin be used to install both starter and trim strips. Some, however, will exist more useful when installing trim strips.
- Tape measure: You lot will demand a measuring tape to measure the area on which the starter strip will be installed.
- Pencil: Go a pencil or an erasable marker to put marks on your points of measurements. If yous volition be using a marker, all the same, make certain to take white vinegar or rubbing alcohol handy to remove the marks afterwards.
- Nails/screws: These volition be driven into the marked points and through the strips to concord them in place.
- Hammer: Use a claw hammer to drive nails into the marked spots.
- String: Bring a string long enough to cover the length of the wall being sided.
- Level: This will ensure the string runs in a straight line from ane blast to the next.
- Chalk line: Use this to snap a straight line between two nails.
- Caulk (for trim strips): You will use this to seal the openings around doors and windows earlier laying your trim.
- Tin snips: Apply it to cut starter or trim strips where necessary. Yous could as well utilise a utility knife; simply score the strip and break it. Make certain any tool you use for cutting is abrupt to ensure a make clean cut.
- Trim strips: Get J-channel trims, under-sill trims, and base of operations trims.
5 Like shooting fish in a barrel Steps to Install Vinyl Siding Starter Strips
The vinyl siding starter strip, as the name suggests, is installed before the get-go row of the siding to help keep the planks level and straight. It ordinarily has a locking channel to which the first siding plank attaches.
This strip must be installed correctly if you hope to lay the rest of the siding properly and salve yourself hours of disappointment after on. Here is how to install vinyl siding starter strips the correct mode:
Step 1: Find the Lowest Signal of the Wall
Examine the wall you want to side to find its everyman corner. Then, from this corner, use a tape mensurate to take a measurement that is up to a ¼ inch less than the width of your starter strip. Marker the point with a pencil. It is important to pick a corner that has sheathing to give the strip a strong construction.
Pace 2: Drive a Nail Into the Marked Point
Using a claw hammer, hitting a blast into the marked surface area. Do non bulldoze it all the way through; hammer it partially, as y'all will still need to pull information technology out later on the installation is washed.
Stride 3: Tie a String Around the Nail
Grab a long string and make a knot around the nail you just hammered to the wall. Stretch the string as you walk to the contrary corner of the wall, making sure to apply a level to go on the thread aligned with the nail.
At present, partially drive another nail into the wall in this other corner, ensuring information technology aligns with the offset boom. Extend a chalk line between the 2 nails and remove the thread and nails.
Footstep 4: Mensurate the Widths of the Corner Posts
Using a tape mensurate, go the widths of both the inner and outer corner posts of the wall you are siding. And then, measure the bottom of the wall from the corner, leaving an allowance of the corner posts and an extra ¼ inch.
Step 5: Position the Starter Strip
Place the finish of your starter strip at the point where you lot take made the measurement, with its top edge aligned with the chalk line.
Bulldoze nails or screws into the strip's nailing slots, leaving a distance of most ten inches between one nail to the next.
Install more starter strips along the chalk line, as necessary, until you accept covered the entire length of the wall. In one case you are washed, proceed to the balance of the walls using the same technique y'all accept used in the offset wall.
If yous follow the above procedure keenly, you will be able to install your vinyl siding starter strips without having to enlist the services of a professional. Here is a video that explains the installation procedure in detail.
iii Quick Steps to Install Vinyl Siding Trim Strips
Vinyl siding trim strips are used to encase doors and windows to create focal points and add curb appeal. While they may appear simply cosmetic, trim strips play a huge role in finishing the seams around doors and windows, which helps go on moisture at bay.
Not sure how to install vinyl siding trim strips? Follow the easy steps below.
Step 1: Create a Seal for Air and Wet
Before y'all install door and window trims, brand sure to first apply a filler or sealant effectually the openings. It will aid go on the area around the trim air and moisture proof.
Once washed, become alee with your installation, starting from the tops, then the sides, and finishing with the bottoms. For the tops, you will be installing j-aqueduct trims with a horizontal siding and base trims with a vertical siding.
Pace ii: Cut the Trims
Using a utility pocketknife or a pair of can snips, cut the trim strip such that it's 2 channel widths longer than the width of the opening.
Step 3: Attach the Trim
Put the top trim in place and drive nails into the blast slots at the heart, with the nails being 10 inches apart. Next, install the side pieces, hammering each nail 12 inches away from the adjacent. At the bottom, install a J-channel trim for the vertical siding and an under-sill trim for the horizontal siding.
Echo the in a higher place steps to install trim strips on the residuum of the doors and windows. To go a meliorate understanding of how to install vinyl siding trim strips, watch this video.
Additional Tips for Installing Vinyl Siding Starter & Trim Strips
Start With a Flat Surface
For best results, make sure the surface of the wall on which you lay your strips is apartment and level. This is especially important when installing starter strips. Keep in mind that the rest of the siding will just be directly if the starter strip itself is straight.
Employ a Conditions Resistant Barrier
This does not but apply to the starter or trim strips but to the remainder of the planks also. You should ready up a skillful conditions-resistant blockade before installing the siding. This volition help keep the wall structure from arresting moisture, which will foreclose the evolution of mold and mildew.
Trims Should Freely Move From Side to Side
When installing your vinyl siding starter and trim strips, you accept to call back that these panels tin can expand and contract with temperature changes.
And so, whether you are using nails, staples, or screws to fasten the trims, avert driving the caput of the fastener likewise shut to the wall. Tight nailing, stapling, or screwing will crusade the trim to buckle when the temperature changes.
Follow the Recommended Cut Guidelines
If you are cutting a strip, it is important that you pay attention to the instructions given by the manufacturer. When using tin snips, for instance, avoid having the blades completely closed as yous end a stroke then yous tin have a cleaner, neater cut.
If you are using a utility knife, score the strip face up and snap it backward. Yous don't have to score all the way through the panel.
Habiliment Protective Gear
As with whatsoever construction job, wear safety gear when installing vinyl siding starter and trim strips. Gloves and safety goggles, especially, are important in all operations that involve cutting and nailing.
Don't Exist Agape to Ask for Help
If you lot are not certain what to practice or where to buy the all-time tools and materials for the job, go help from others. Talk to building experts in your expanse to know what works. Yous could also get useful insights from online builders' forums like this i.
The Takeaway
The starter and trim strips are an important part of vinyl siding installation, as they both help amend the house's structure and appearance. You can easily set these up using the steps laid out above.
To guarantee the best results, brand sure the surface on which you lay the panels is level then the remainder of the siding can also be straight. It would also help to do a bit of research to know where to buy the best supplies for the job.
Source: https://www.whatisvinyl.com/how-to-install-vinyl-siding-starter-trim-strips/
Posted by: lanceoverects.blogspot.com
0 Response to "Do You Nail Starter Strips Tight For Vinyl Siding"
Post a Comment